FREE CROSSBEAMS & COCKPIT FOR TIKI 26 - Wharram Builders and Friends2024-03-29T11:16:13Zhttp://wharrambuilders.ning.com/forum/topics/free-crossbeams-cockpit-for-tiki-26?commentId=2195841%3AComment%3A173789&xg_source=activity&feed=yes&xn_auth=noNo problem, it's a bit of a "…tag:wharrambuilders.ning.com,2020-08-05:2195841:Comment:1737892020-08-05T16:06:47.091ZRobert Hugheshttp://wharrambuilders.ning.com/profile/RobertHughes
<p>No problem, it's a bit of a "niche market" so nobody else is after them at this moment...</p>
<p>No problem, it's a bit of a "niche market" so nobody else is after them at this moment...</p> Definitely interested in the…tag:wharrambuilders.ning.com,2020-08-05:2195841:Comment:1736892020-08-05T14:02:13.642ZShoestringhttp://wharrambuilders.ning.com/profile/Shoestring
<p>Definitely interested in the whole lot, will check with JWD to see if it will fit a standard T26.</p>
<p>Thanks for your patience.</p>
<p></p>
<p>Definitely interested in the whole lot, will check with JWD to see if it will fit a standard T26.</p>
<p>Thanks for your patience.</p>
<p></p> Ok, that's fine.
If it's any…tag:wharrambuilders.ning.com,2020-08-02:2195841:Comment:1736182020-08-02T05:59:03.982ZRobert Hugheshttp://wharrambuilders.ning.com/profile/RobertHughes
<p>Ok, that's fine.</p>
<p>If it's any help, I'm happy to let the cockpit or either of the beams go separately. All I wouldn't do is let someone just take the hardware (winches etc).</p>
<p>Cheers</p>
<p>Rob</p>
<p>Ok, that's fine.</p>
<p>If it's any help, I'm happy to let the cockpit or either of the beams go separately. All I wouldn't do is let someone just take the hardware (winches etc).</p>
<p>Cheers</p>
<p>Rob</p> Thanks for the detailed reply…tag:wharrambuilders.ning.com,2020-08-01:2195841:Comment:1736172020-08-01T21:56:25.489ZShoestringhttp://wharrambuilders.ning.com/profile/Shoestring
<p>Thanks for the detailed reply Rob, appreciate it.</p>
<p>I'll do a bit more research and see if they might be made to fit and get back to you soon.</p>
<p>All the best,</p>
<p></p>
<p>Joel</p>
<p></p>
<p>Thanks for the detailed reply Rob, appreciate it.</p>
<p>I'll do a bit more research and see if they might be made to fit and get back to you soon.</p>
<p>All the best,</p>
<p></p>
<p>Joel</p>
<p></p> I'm afraid I don't. They las…tag:wharrambuilders.ning.com,2020-07-31:2195841:Comment:1735202020-07-31T07:10:14.966ZRobert Hugheshttp://wharrambuilders.ning.com/profile/RobertHughes
<p>I'm afraid I don't. They lash down with cord so that part should be simple enough. I suspect the way they taper towards the ends is unlikely to be exactly the same, so the locating blocks would probably need to be altered.</p>
<p>Essentially these have a flat bottom with a hardwood block about 3" square and 3/4" thick under each lashing point. Those blocks locate into L shaped hardwood pads on the deck which support the beams. You would have to make those to blocks fit. The blocks on…</p>
<p>I'm afraid I don't. They lash down with cord so that part should be simple enough. I suspect the way they taper towards the ends is unlikely to be exactly the same, so the locating blocks would probably need to be altered.</p>
<p>Essentially these have a flat bottom with a hardwood block about 3" square and 3/4" thick under each lashing point. Those blocks locate into L shaped hardwood pads on the deck which support the beams. You would have to make those to blocks fit. The blocks on the beams are just screwed and epoxied to the bottom so you could cut them off and fit new ones in different places if you needed to.</p>
<p>The cockpit hangs from the beams so it doesn't know what sort of hulls it's attached to... There's a gap between the cockpit and hulls where plywood seats are lashed on top (I don't have them)</p>
<p>I'm near Portsmouth and if you ever get over this way you're welcome to pop in and have a look.</p>
<p>Cheers</p>
<p>Rob</p> Hi,
Thanks for the reply - do…tag:wharrambuilders.ning.com,2020-07-30:2195841:Comment:1735162020-07-30T22:00:18.458ZShoestringhttp://wharrambuilders.ning.com/profile/Shoestring
<p>Hi,</p>
<p>Thanks for the reply - do you know if these would fit on a conventional ply/epoxy Tiki 26?</p>
<p>All the best</p>
<p>Hi,</p>
<p>Thanks for the reply - do you know if these would fit on a conventional ply/epoxy Tiki 26?</p>
<p>All the best</p> Hi Joel, yes they are.
Cheers…tag:wharrambuilders.ning.com,2020-07-28:2195841:Comment:1735072020-07-28T13:14:20.677ZRobert Hugheshttp://wharrambuilders.ning.com/profile/RobertHughes
<p>Hi Joel, yes they are.</p>
<p>Cheers</p>
<p>Rob</p>
<p>Hi Joel, yes they are.</p>
<p>Cheers</p>
<p>Rob</p> Hi Robert,
Just wondering if…tag:wharrambuilders.ning.com,2020-07-28:2195841:Comment:1735042020-07-28T11:21:33.080ZShoestringhttp://wharrambuilders.ning.com/profile/Shoestring
<p>Hi Robert,</p>
<p>Just wondering if the cockpit and beams are still available?</p>
<p>Thanks,</p>
<p></p>
<p>Joel</p>
<p>Hi Robert,</p>
<p>Just wondering if the cockpit and beams are still available?</p>
<p>Thanks,</p>
<p></p>
<p>Joel</p>