Bulkhead 3 and 6 - Wharram Builders and Friends2024-03-29T12:00:35Zhttp://wharrambuilders.ning.com/forum/topics/bulkhead-3-and-6?feed=yes&xn_auth=noThanks for the advice!tag:wharrambuilders.ning.com,2014-12-12:2195841:Comment:1236882014-12-12T14:29:22.506ZJames Ryan davenporthttp://wharrambuilders.ning.com/profile/JamesRyandavenport
<p>Thanks for the advice!</p>
<p>Thanks for the advice!</p> I second the extra couple of…tag:wharrambuilders.ning.com,2014-12-12:2195841:Comment:1237692014-12-12T12:45:59.371ZMarc LaFrancehttp://wharrambuilders.ning.com/profile/MarcLaFrance
<p>I second the extra couple of sheets. You'll find uses for the extra scraps , later.</p>
<p>I second the extra couple of sheets. You'll find uses for the extra scraps , later.</p> I guess the two sheet method…tag:wharrambuilders.ning.com,2014-12-12:2195841:Comment:1238532014-12-12T12:02:38.287ZJames Ryan davenporthttp://wharrambuilders.ning.com/profile/JamesRyandavenport
I guess the two sheet method in the plans is for minimizing plywood waste by using two smaller sheets. I think I will buy a cpl of extra sheets and cut them out of one sheet each.
I guess the two sheet method in the plans is for minimizing plywood waste by using two smaller sheets. I think I will buy a cpl of extra sheets and cut them out of one sheet each. Ok, my memory is returning. I…tag:wharrambuilders.ning.com,2014-12-12:2195841:Comment:1236862014-12-12T01:58:06.271ZBudget Boaterhttp://wharrambuilders.ning.com/profile/BudgetBoater
<p>Ok, my memory is returning. It was a long time ago that I built my T-30, and the plans went with the boat when I sold it.</p>
<p></p>
<p>All of the bulkheads are cut one piece. The lower bulkheads came from a couple of sheets of ply, and all of the upper bulkheads and ring frames were cut in full from a few sheets of ply. Just look at your ply cut sheet to see how they all get cut on the plywood. There is no need for butt blocks. The beam of each hull is far less than 8', so the upper…</p>
<p>Ok, my memory is returning. It was a long time ago that I built my T-30, and the plans went with the boat when I sold it.</p>
<p></p>
<p>All of the bulkheads are cut one piece. The lower bulkheads came from a couple of sheets of ply, and all of the upper bulkheads and ring frames were cut in full from a few sheets of ply. Just look at your ply cut sheet to see how they all get cut on the plywood. There is no need for butt blocks. The beam of each hull is far less than 8', so the upper bulkheads are cut from the ply laid on its side, same as the Tiki 38.</p> I cut in only one sheet, but…tag:wharrambuilders.ning.com,2014-12-12:2195841:Comment:1236832014-12-12T00:48:15.871ZRogerio Martinhttp://wharrambuilders.ning.com/profile/RogerioMartin
<p>I cut in only one sheet, but I was have extra plys.</p>
<p>is secure, all wharran joints (buttblocks) is secure. when you joint with buttblocks, you double your thickness</p>
<p>I cut in only one sheet, but I was have extra plys.</p>
<p>is secure, all wharran joints (buttblocks) is secure. when you joint with buttblocks, you double your thickness</p> I just looked it up in the pl…tag:wharrambuilders.ning.com,2014-12-10:2195841:Comment:1239502014-12-10T23:54:02.193ZRicardo Aráozhttp://wharrambuilders.ning.com/profile/RicardoAraoz
<p>I just looked it up in the plans. It would seem you are right, the butt blocks are not mentioned. But if the butt blocks for the side panels are specified at 100 mm width (9 mm panels), then I would guess a 700 mm width butt block for the 6 mm bulkheads will be enough.</p>
<p></p>
<p>I just looked it up in the plans. It would seem you are right, the butt blocks are not mentioned. But if the butt blocks for the side panels are specified at 100 mm width (9 mm panels), then I would guess a 700 mm width butt block for the 6 mm bulkheads will be enough.</p>
<p></p> Thanks,
I see the but blocks…tag:wharrambuilders.ning.com,2014-12-10:2195841:Comment:1239492014-12-10T21:17:06.457ZJames Ryan davenporthttp://wharrambuilders.ning.com/profile/JamesRyandavenport
<p>Thanks, </p>
<p>I see the but blocks for the sides panels but not for the bulkheads.</p>
<p>Thanks, </p>
<p>I see the but blocks for the sides panels but not for the bulkheads.</p> They are joined with a butt p…tag:wharrambuilders.ning.com,2014-12-09:2195841:Comment:1238432014-12-09T13:49:53.172ZBudget Boaterhttp://wharrambuilders.ning.com/profile/BudgetBoater
<p>They are joined with a butt plate. This is shown on the plans.</p>
<p>They are joined with a butt plate. This is shown on the plans.</p> On Tiki 30tag:wharrambuilders.ning.com,2014-12-09:2195841:Comment:1238422014-12-09T13:25:27.175ZJames Ryan davenporthttp://wharrambuilders.ning.com/profile/JamesRyandavenport
<p>On Tiki 30</p>
<p>On Tiki 30</p> Tiki 30tag:wharrambuilders.ning.com,2014-12-09:2195841:Comment:1237522014-12-09T13:24:50.935ZJames Ryan davenporthttp://wharrambuilders.ning.com/profile/JamesRyandavenport
<p>Tiki 30</p>
<p>Tiki 30</p>